SMC SMCGS8P Guia de Instalação

INSTALLATION GUIDEInstallationsanleitungEZ SwitchTM 10/100/10008-Port Web Smart Switch with PoESMCGS8P-Smart

viImportant! Before making connections, make sure you have the correct cord set. Check it (read the label on the cable) against the following: Veuill

viiFrance et Pérou uniquement:Ce groupe ne peut pas être alimenté par un dispositif à impédance à la terre. Si vos alimentations sont du type impédanc

viiiWarnings and Cautionary MessagesWarnings (in German)Stromkabel. Dies muss von dem Land, in dem es benutzt wird geprüft werden: Schweiz Dieser Str

ixEnvironmental StatementThe manufacturer of this product endeavours to sustain an environmentally-friendly policy throughout the entire production pr

x

xiContentsChapter 1: Introduction 1-1Overview 1-1Switch Architecture 1-2Power-over-Ethernet Capability 1-2Network Management Options 1-2Descriptio

xiiContentsChapter 4: Making Network Connections 4-1Connecting Network Devices 4-1Twisted-Pair Devices 4-1Power-over-Ethernet Connections 4-1Cabli

xiiiContentsRack-Montage D-2GlossaryIndex

xivContents

xvTablesTable 1-1 Port Status LEDs 1-4Table 1-2 Power Status LED 1-4Table 4-1 Maximum 1000BASE-T Gigabit Ethernet Cable Length 4-6Table 4-2 Maximum

xviFiguresFigure 1-1 Front Panel 1-1Figure 1-2 Rear Panel 1-1Figure 1-3 Port and Power LEDs 1-3Figure 1-4 Power Supply Socket 1-4Figure 2-1 PoE Co

1-1Chapter 1: IntroductionOverviewThe SMCGS8P-Smart is an intelligent Layer 2 switch with 8 10/100/1000BASE-T ports, one of which is a Gigabit combina

Introduction1-21Switch ArchitectureThe switch employs a wire-speed, non-blocking switching fabric. This permits simultaneous wire-speed transport of m

Description of Hardware1-31Description of Hardware10/100/1000BASE-T PortsThe switch contains 8 RJ-45 ports that operate at 10 Mbps or 100 Mbps, half o

Introduction1-41Power Supply SocketThe power socket is located on the rear panel of the switch. The standard power socket is for the AC power cord.Fig

Features and Benefits1-51Features and BenefitsConnectivity• 8 10/100/1000 Mbps ports for easy Gigabit Ethernet integration and for protection of your

Introduction1-61

2-1Chapter 2: Network PlanningIntroduction to SwitchingA network switch allows simultaneous transmission of multiple packets via non-crossbar switchin

Network Planning2-22Application ExamplesThe switch is not only designed to segment your network, but also to provide a wide range of options in settin

Application Examples2-32Figure 2-2 Collapsed BackboneMeeting RoomWith 8 1000Mbps parallel bridging ports (i.e., 8 distinct collision domains), this s

20 MasonIrvine, CA 92618Phone: (949) 679-8000EZ Switch 10/100/1000Installation GuideFrom SMC’s EZ line of low-cost workgroup LAN solutionsJune 2007Pub

Network Planning2-42Making VLAN ConnectionsThe switch supports VLANs that can be used to organize any group of network nodes into separate broadcast d

Application Notes2-52Application Notes1. Full-duplex operation only applies to point-to-point access (such as when a switch is attached to a workstati

Network Planning2-62

3-1Chapter 3: Installing the SwitchSelecting a Siteswitch units can be mounted in a standard 19-inch equipment rack or on a flat surface. Be sure to f

Installing the Switch3-23Figure 3-1 RJ-45 ConnectionsEquipment ChecklistAfter unpacking the switch unit, check the contents to be sure you have recei

Mounting3-33Rack MountingBefore rack mounting the switch, pay particular attention to the following factors:• Temperature: Since the temperature with

Installing the Switch3-432. Mount the device in the rack, using four rack-mounting screws (not provided).Figure 3-3 Installing the Switch in a Rack3.

Installing an Optional SFP Transceiver3-532. Set the device on a flat surface near an AC power source, making sure there are at least two inches of sp

Installing the Switch3-63Connecting to a Power SourceTo connect a device to a power source:1. Insert the power cable plug directly into the socket loc

4-1Chapter 4: Making Network ConnectionsConnecting Network DevicesThe switch units are designed to interconnect multiple segments (or collision domain

Information furnished by SMC Networks, Inc. (SMC) is believed to be accurate and reliable. However, no responsibility is assumed by SMC for its use, n

Making Network Connections4-24Cabling GuidelinesThe RJ-45 ports on the switch support automatic MDI/MDI-X pinout configuration, so you can use standar

Twisted-Pair Devices4-34Network Wiring ConnectionsToday, the punch-down block is an integral part of many of the newer equipment racks. It is actually

Making Network Connections4-44Fiber Optic SFP DevicesAn optional Gigabit SFP transceiver (1000BASE-SX, 1000BASE-LX or 1000BASE-LH) can be used for a b

Fiber Optic SFP Devices4-543. Connect one end of the cable to the LC port on the switch and the other end to the LC port on the other device. Since LC

Making Network Connections4-64Connectivity RulesWhen adding hubs (repeaters) to your network, please follow the connectivity rules listed in the manua

Connectivity Rules4-74100 Mbps Fast Ethernet Collision Domain10 Mbps Ethernet Collision DomainTable 4-5 Maximum Fast Ethernet Cable LengthType Cable

Making Network Connections4-84Cable Labeling and Connection RecordsWhen planning a network installation, it is essential to label the opposing ends of

A-1Appendix A: TroubleshootingDiagnosing Switch Indicators Power and Cooling ProblemsIf the power indicator does not turn on when the power cord is pl

TroubleshootingA-2AInstallationVerify that all system components have been properly installed. If one or more components appear to be malfunctioning (

B-1Appendix B: CablesTwisted-Pair Cable and Pin AssignmentsFor 10BASE-T/100BASE-TX connections, a twisted-pair cable must have two pairs of wires. For

iLimited WarrantyLimited Warranty Statement: SMC Networks, Inc. (“SMC”) warrants its products to be free from defects in workmanship and materials, un

CablesB-2BTable B-1 10/100BASE-TX MDI-X and MDI Port PinoutsStraight-Through WiringIf the twisted-pair cable is to join two ports and only one of the

Twisted-Pair Cable and Pin AssignmentsB-3Bany RJ-45 port on the switch, you can use either straight-through or crossover cable to connect to any devic

CablesB-4BCable Testing for Existing Category 5 CableInstalled Category 5 cabling must pass tests for Attenuation, Near-End Crosstalk (NEXT), and Far-

C-1Appendix C: SpecificationsPhysical CharacteristicsPorts8 10/100/1000BASE-T, with auto-negotiation1 SFP transceiver slot.Network InterfacePorts 1-8:

SpecificationsC-2CAC Input100 to 240 V, 50-60 Hz, 1.5 APower-over-EthernetInput voltage: 48 V DCMaximum output power 60 W: 7.5 W per port for eight

StandardsC-3CStandardsIEEE 802.3-2005 Ethernet, Fast Ethernet, Gigabit EthernetIEEE 802.3af Power-over-EthernetIEEE 802.1D Spanning Tree ProtocolIEEE

SpecificationsC-4C

D-1Appendix D: German InstructionsEine Site Auswählen (Selecting a Site)Die Schalter können in ein Standard-19-Zoll-Ausrüstungsgestell oder auf eine f

German InstructionsD-2DMontage (Rack Mounting Instructions)Switch-Einheiten können an ein standardmäßiges 19-Zoll Einrichtungsrack, einen Arbeitstisch

Glossary-1Glossary10BASE-TIEEE 802.3 specification for 10 Mbps Ethernet over two pairs of Category 3 or better UTP cable.100BASE-TXIEEE 802.3u specifi

iiNOT BE LIABLE UNDER THIS WARRANTY IF ITS TESTING AND EXAMINATION DISCLOSE THE ALLEGED DEFECT IN THE PRODUCT DOES NOT EXIST OR WAS CAUSED BY CUSTOME

GlossaryGlossary-2CSMA/CDCSMA/CD (Carrier Sense Multiple Access/Collision Detect) is the communication method employed by Ethernet, Fast Ethernet, or

Glossary-3GlossaryIEEE 802.3xDefines Ethernet frame start and stop requests and timers used for flow control on full-duplex links. (Now incorporated i

GlossaryGlossary-4Redundant Power Supply (RPS)A backup power supply unit that automatically takes over in case the primary power supply should fail. R

Index-1Numerics10 Mbps connectivity rules 4-7100 Mbps connectivity rules 4-71000 Mbps connectivity rules 4-61000BASE-LX fiber cable lengths 4-61000BAS

IndexIndex-2Mmanagementagent 1-2features 1-5, C-2SNMP 1-2mounting the switchin a rack 3-3on a desktop or shelf 3-4Nnetworkconnections 4-1examples 2-2P

20 Mason • Irvine, CA 92618 • Phn: 949-679-8000 • www.smc.comSMCGS8P-SmartTECHNICAL SUPPORTFrom U.S.A. and Canada (24 hours a day, 7 days a week)Phn:

iiiCompliances and Safety WarningsFCC - Class AThis equipment has been tested and found to comply with the limits for a Class A digital device, pursua

ivCE Mark Declaration of Conformance for EMI and Safety (EEC)This information technology equipment complies with the requirements of the Council Dire

vWarnhinweis: Faseroptikanschlüsse - Optische SicherheitPower Cord SafetyPlease read the following safety information carefully before installing this