SMC TigerAccess Especificações Página 155
- Página / 387
- Índice
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
CLI Management Guide
TigerAccess™ EE
154 SMC7824M/VSW
7.3.6 Reinitiating Delay
To configure the interval time of enabling LLDP frame after configuring LLDP operation
type, use the following command.
Command Mode Description
lldp reinitdelay <1-10> Bridge
Configures the interval time of enabling LLDP frame
from the time of configuring not to process LLDP
frame. (default: 2)
To configure delay time of transmitting LLDP frame, use the following command.
Command Mode Description
lldp txdelay <1-8192> Bridge
Configures delay time of transmitting LLDP frame.
(default: 2)
7.3.7 Displaying LLDP Configuration
To display LLDP configuration, use the following command.
Command Mode Description
show lldp config [PORTS] Shows LLDP configuration.
show lldp remote [PORTS] Show statistics for remote entries.
show lldp statistics [PORTS]
Enable
Global
Bridge
Shows LLDP operation and statistics.
To delete an accumulated statistics on the port, use the following command.
Command Mode Description
clear lldp statistics [PORTS]
Enable
Global
Bridge
Deletes an accumulated statistics on the port.
The following is the sample output of the show lldp config command.
SWITCH(config)# show lldp config 1-2
GLOBL:
-----------------------------------------------------------------------
MsgTxInterval = 30
MsgTxHold = 4 => txTTL = 120
ReInitDelay = 2
TxDelay = 2
-----------------------------------------------------------------------
PORTS active adminStat| mgmtAddress|optTLVs
1: disable Tx<->Rx| none|
2: disable Tx<->Rx| none|
SWITCH(config)#
- Reason for Update 4
- Issue History 4
- Contents 5
- Illustrations 17
- 1 Introduction 20
- 1.3 Document Convention 21
- 1.4 Document Notation 21
- 1.5 Virus Protection 22
- 2 System Overview 23
- 2.1 System Features 24
- 3.1 Configuration Mode 26
- Command Description 32
- 3.3 Useful Tips 33
- 3.3.3 Using Abbreviation 36
- 4.1 System Connection 37
- 4.1.6.2 Security Level 41
- 4.1.8 Auto Log-out 45
- 4.1.9 Telnet Access 45
- 4.1.10 System Rebooting 46
- 4.2 System Authentication 48
- 4.2.4 RADIUS Server 49
- 4.2.5 TACACS+ Server 50
- 4.2.6 Accounting Mode 51
- 4.3 Configuring Interface 52
- 4.3.4 Interface Description 54
- 4.3.5 Displaying Interface 55
- 4.4 Secure Shell (SSH) 56
- 4.4.2 SSH Client 57
- 4.4.2.3 Authentication Key 58
- 4.5 802.1x Authentication 59
- 4.5.1 802.1x Authentication 60
- 4.5.1.3 Authentication Mode 61
- 4.5.1.4 Authentication Port 62
- 4.5.1.5 Force Authorization 62
- 4.5.7 Sample Configuration 66
- 5 Port Configuration 68
- 5.2.3 Transmit Rate 69
- 5.2.4 Duplex Mode 70
- 5.2.5 Flow Control 71
- 5.2.6 Port Description 71
- 5.2.7 Traffic Statistics 72
- 5.2.7.2 CPU Statistics 73
- 5.2.7.3 Protocol Statistics 74
- 5.2.8 Port Information 75
- 5.3 VDSL Port Configuration 76
- 5.3.2 Configuring VDSL Port 77
- 5.3.2.2 Enabling VDSL Port 78
- 5.3.2.5 PSD Level 84
- 5.3.2.6 PSD Mask Level 85
- 5.3.2.7 Interleave 85
- 5.3.2.10 Ham-band 88
- 5.3.2.11 SNR Margin 89
- 5.3.2.13 G.handshake Tone 92
- 5.3.4 Config-Profile 96
- 5.3.5 Configuring CPE 103
- 5.3.5.8 Duplex mode of CPE 108
- Feature Command 110
- 5.4 Port Mirroring 111
- 6 System Environment 113
- 6.1.3 Time Zone 114
- 6.1.6 Terminal Configuration 116
- 6.1.7 Login Banner 116
- 6.1.8 DNS Server 117
- 6.1.9 Fan Operation 118
- 6.1.11 FTP Server 118
- 6.1.12 FTP Client address 119
- 6.1.13 System Threshold 119
- 6.1.13.2 Port Traffic 120
- 6.1.13.3 Fan Operation 120
- 6.1.13.4 System Temperature 121
- 6.1.13.5 System Memory 121
- 6.2 Configuration Management 124
- 6.2.3 Auto-Saving 125
- 6.3 System Management 127
- 6.3.3 Tracing Packet Route 130
- 6.3.5 MAC Table 132
- 6.3.7 System Information 132
- 6.3.9 Running Process 133
- 6.3.12 Default OS 134
- 6.3.13 Switch Status 134
- 7 Network Management 136
- 7.1.3 SNMP Com2sec 138
- 7.1.4 SNMP Group 138
- 7.1.5 SNMP View Record 139
- 7.1.7 SNMP Version 3 User 140
- 7.1.8 SNMP Trap 140
- 7.1.8.2 SNMP Trap Host 141
- 7.1.8.4 Disabling SNMP Trap 142
- 7.1.8.5 Displaying SNMP Trap 143
- 7.1.9 SNMP Alarm 144
- 7.1.9.5 ADVA Alarm Severity 147
- 7.1.9.6 ERP Alarm Severity 148
- 7.1.11 Disabling SNMP 149
- 7.2.1 OAM Loopback 150
- 7.2.2 Local OAM Mode 151
- 7.2.3 OAM Unidirection 151
- 7.2.4 Remote OAM 151
- 7.3.1 LLDP Operation 153
- 7.3.2 Enabling LLDP 153
- 7.3.3 LLDP Operation Type 154
- 7.3.4 Basic TLV 154
- 7.3.5 LLDP Message 154
- 7.3.6 Reinitiating Delay 155
- 7.4 Remote Monitoring (RMON) 156
- 7.4.2 RMON Alarm 159
- 7.4.3 RMON Event 162
- 7.4.3.4 Event Type 163
- 7.5 Syslog 164
- 7.5.2 Facility Code 166
- 7.5.3 Syslog Bind Address 167
- 7.5.5 Disabling Syslog 167
- 7.6 Quality of Service(QoS) 169
- 7.6.1 How to Operate QoS 170
- 7.6.2 Packet Classification 172
- 7.6.2.4 Class Creation 175
- 7.6.3 Packet Conditioning 176
- 7.6.3.2 Packet Counter 177
- 7.6.3.4 Rate-limit 178
- 7.6.4 Rule Action 179
- 7.6.4.2 Metering 180
- 7.6.4.3 Policy Priority 186
- 7.6.4.4 Policy Action 186
- Packet Ingress 187
- Ingress Processing 187
- 7.6.5 Displaying Rule 191
- 7.6.6 Admin Rule 193
- 7.6.6.4 Class Creation 195
- 7.6.7 Admin Rule Action 196
- 7.6.7.3 Admin Policy Action 197
- 7.6.8 Displaying Admin Rule 198
- 7.6.9 Scheduling Algorithm 199
- 7.6.9.1 Scheduling Mode 201
- 7.6.9.2 Weight 201
- 7.6.9.5 Queue Status 203
- 7.6.9.6 Displaying QoS 203
- Start End 204
- Queue Length 204
- Probability 204
- Internet 206
- 7.8 Max New Hosts 207
- 7.9 Port Security 208
- 7.9.2 Port Security Aging 209
- 7.10 MAC Table 210
- 7.11 MAC Filtering 211
- 7.12.1 ARP Table 214
- 7.12.2 ARP Alias 215
- 7.12.3 ARP Inspection 216
- 7.12.4 Gratuitous ARP 221
- 7.12.5 Proxy-ARP 223
- 7.13 ICMP Message Control 224
- 7.14 TCP Flag Control 227
- 7.15 Packet Dump 227
- 7.15.3 Debug Packet Dump 229
- Packet sample 230
- Interface counter 230
- Packet samples 230
- 7.16.1 sFlow Service 231
- 7.16.2 Agent IP Address 231
- 7.16.5 Counter Interval 232
- 7.16.6 Sample Rate 232
- 7.16.7 Configuring Receiver 233
- 7.16.8 Receiver Index 234
- 7.16.9 Displaying sFlow 234
- 8 System Main Functions 235
- 8.1.1.1 Creating VLAN 237
- 8.1.1.2 Specifying PVID 237
- 8.1.1.4 Deleting VLAN 237
- 8.1.2 Protocol-based VLAN 238
- 8.1.3 MAC-based VLAN 238
- 8.1.6 VLAN Description 240
- 8.1.7 VLAN Precedence 241
- 8.1.10 Layer 2 Isolation 244
- 8.1.10.1 Shared VLAN 245
- 8.1.11 VLAN Translation 247
- 8.1.12 Sample Configuration 247
- Switch 1 Switch 2 249
- Outer Network 250
- Uplink Port 250
- 8.2 Link Aggregation 252
- 8.2.2.1 Configuring LACP 254
- 8.2.2.2 Operation Mode 255
- 8.2.2.3 Priority of Switch 255
- 8.2.2.4 Manual Aggregation 255
- 8.2.2.6 Administrational Key 256
- 8.2.2.7 Port Priority 257
- Switch A Switch B 258
- PC-A PC-B 258
- 8.3.1 STP Operation 259
- Blocking 262
- Listening 262
- Learning 262
- Forwarding 262
- Disabled 262
- 8.3.2 RSTP Operation 263
- 8.3.3 MSTP Operation 267
- 8.3.3.1 MSTP 268
- Region B (IST) 269
- Region A (IST) 269
- Region C (IST) 269
- 8.3.6.1 Path-cost Method 270
- 8.3.6.2 Edge Ports 271
- 8.3.6.4 Port Priority 272
- 8.3.6.5 Link Type 273
- 8.3.7 Configuring MSTP 274
- 8.3.7.3 Port Priority 275
- 8.3.7.4 MST Region 275
- 8.3.8 Configuring PVSTP 278
- 8.3.8.2 Root Switch 279
- 8.3.8.3 Path-cost 279
- 8.3.8.4 Port Priority 280
- 8.3.9 Root Guard 281
- 8.3.11 Loop Back Detection 282
- 8.3.12 BPDU Configuration 283
- 8.3.12.1 Hello Time 284
- 8.3.12.2 Forward Delay Time 284
- 8.3.12.3 Max Age 285
- 8.3.12.4 BPDU Hop Count 285
- 8.3.12.5 BPDU Filtering 286
- 8.3.12.6 BPDU Guard 286
- 8.3.13 Sample Configuration 288
- VLAN 101 ~ 200 289
- 8.4.1 ERP Mechanism 290
- 8.4.3 ERP Shared Link 294
- 8.4.4.1 ERP Domain Name 295
- 8.4.4.3 Protected VLAN 295
- 8.4.4.4 Control VLAN 296
- 8.4.4.5 ERP Ring Priority 296
- 8.4.5 Selecting the Node 297
- 8.4.6 Protected Activation 297
- 8.4.8 Wait-to-Restore Time 298
- 8.4.9 Learning Disable Time 298
- 8.4.10 Test Packet Interval 299
- 8.4.11 LOTP Hold Off Time 299
- 8.4.12 ERP Trap 300
- 8.5 Loop Detection 301
- 8.6.1 DHCP Server 304
- 8.6.1.1 DHCP Pool Creation 305
- 8.6.1.2 DHCP Subnet 305
- 8.6.1.3 Range of IP Address 305
- 8.6.1.4 Default Gateway 306
- 8.6.1.5 IP Lease Time 306
- 8.6.1.6 DNS Server 307
- 8.6.1.7 Manual Binding 307
- 8.6.1.8 Domain Name 308
- 8.6.1.9 DHCP Server Option 308
- 8.6.1.10 Static Mapping 308
- 8.6.1.13 Authorized ARP 310
- 8.6.2.2 DHCP Class Creation 313
- 8.6.3 DHCP Lease Database 314
- 8.6.4 DHCP Relay Agent 316
- Enters the DHCP option mode 319
- 8.6.6 DHCP Option 82 321
- 8.6.7 DHCP Snooping 324
- 8.6.7.2 DHCP Trust State 325
- 8.6.7.3 DHCP Rate Limit 326
- 8.6.7.4 DHCP Lease Limit 326
- 8.6.7.9 Authorized ARP 329
- 8.6.8 IP Source Guard 332
- 8.6.9 DHCP Client 335
- 8.6.9.5 IP Lease Time 336
- 8.6.9.6 Requesting Option 336
- 8.6.10 DHCP Filtering 337
- DHCP Server A 338
- Client 1 Client 2 338
- Client 3 338
- 8.7 Single IP Management 339
- 8.7.3 Disabling Stacking 340
- NODE Enable 341
- Accesses to a slave switch 341
- NODE: node number 341
- 8.8 Rate Limit 343
- 8.9 Flood Guard 344
- 8.9.2 CPU Flood-Guard 345
- 8.9.3 Port Flood-Guard 346
- 8.10 Storm Control 347
- 8.11 Jumbo Frame Capacity 347
- 8.12 Bandwidth 348
- 9 IP Multicast 349
- 9.1.1 IGMP Basic 350
- 9.1.1.1 Clearing IGMP Entry 351
- 9.1.1.2 IGMP Debug 351
- 9.1.2 IGMP Version 2 352
- 9.1.2.1 IGMP Static Join 353
- 9.1.3 IGMP Version 3 354
- 9.2 Multicast Functions 355
- 9.2.2 IGMP Snooping Basic 357
- 9.2.3 IGMPv2 Snooping 359
- 9.2.4 IGMPv3 Snooping 368
- 9.2.6.1 Enabling MVR 370
- 9.2.6.2 MVR Group 370
- 9.2.6.3 Source/Receiver Port 371
- 9.2.6.4 MVR Helper Address 371
- 9.2.7.1 IGMP Filtering 372
- 9.2.7.2 IGMP Throttling 374
- 10.1 General Upgrade 376
- 10.2 Boot Mode Upgrade 377
- 10.3 FTP Upgrade 380
- FTP Exits the FTP client 381
- 11 Abbreviations 382
- 20 Mason 386
- Irvine, CA 92618 386
- Phone: (949) 679-8000 386
Manuais e produtos relacionados com Comutadores de rede SMC TigerAccess
(68 páginas)© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.090 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais