SMC EliteConnect Wireless Bridge Guia do Utilizador Página 240
- Página / 318
- Índice
- RESOLUÇÃO DE PROBLEMAS
- MARCADORES
Avaliado. / 5. Com base em avaliações de clientes
Command Line Interface
7-92
7
Command Mode
Interface Configuration (Ethernet)
Command Usage
• DHCP is enabled by default. To manually configure a new IP address, you
must first disable the DHCP client with the no ip dhcp command.
• You must assign an IP address to this device to gain management access
over the network or to connect the access point to existing IP subnets. You
can manually configure a specific IP address using this command, or direct
the device to obtain an address from a DHCP server using the ip dhcp
command. Valid IP addresses consist of four numbers, 0 to 255, separated
by periods. Anything outside this format will not be accepted by the
configuration program.
Example
Related Commands
ip dhcp (7-92)
ip dhcp
This command enables the access point to obtain an IP address from a DHCP
server. Use the no form to restore the default IP address.
Syntax
ip dhcp
no ip dhcp
Default Setting
Enabled
Command Mode
Interface Configuration (Ethernet)
Command Usage
• You must assign an IP address to this device to gain management access
over the network or to connect the access point to existing IP subnets. You
can manually configure a specific IP address using the ip address
command, or direct the device to obtain an address from a DHCP server
using this command.
SMC AP(config)#interface ethernet
Enter Ethernet configuration commands, one per line.
SMC AP(if-ethernet)#ip address 192.168.1.2 255.255.255.0 192.168.1.253
SMC AP(if-ethernet)#
- USER GUIDE 1
- Copyright 3
- Compliances 4
- VCCI Notice 5
- EC Conformance Declaration 5
- Community 5
- Safety Compliance 7
- Power Cord Set 8
- (Germany): 10
- <BASEC> tragen 11
- Table of Contents 12
- Chapter 1: Introduction 20
- Package Checklist 21
- Hardware Description 21
- LED Indicators 22
- Introduction 23
- Ethernet Port 24
- Power Injector Module 24
- Grounding Point 25
- Water Tight Test Point 25
- Features and Benefits 26
- Access Point Topologies 27
- Infrastructure Wireless LAN 28
- Point-to-Point Configuration 30
- Bridge Link Topologies 31
- Network Configuration 32
- Data Rates 33
- Radio Path Planning 33
- Antenna Height 34
- Bridge Link Planning 36
- Radio Interference 37
- Weather Conditions 37
- Grounding 38
- Testing Basic Link Operation 39
- Mount the Unit 39
- Mounting on a Pole 40
- Mounting to a Wall 42
- Connect External Antennas 43
- Connect Cables to the Unit 44
- Ground Wire 45
- Ethernet Cable 45
- Grounding Screw 45
- Align Antennas 46
- Hardware Installation 48
- Required Connections 49
- Initial Configuration Steps 50
- Logging In 51
- Initial Configuration 52
- Advanced Configuration 54
- System Identification 55
- TCP / IP Settings 57
- SSH Settings 63
- Authentication 64
- Filter Control 69
- WDS Settings 73
- AP Management 79
- Administration 80
- Upgrading Firmware 81
- System Log 85
- Configuring SNTP 87
- Configuring SNMPv3 Users 98
- System Configuration 100
- Configuring SNMPv3 Targets 102
- Radio Interface 103
- Radio Settings A (802.11a) 105
- Normal Mode 111
- Turbo Mode 111
- Configuring Wi-Fi Multimedia 114
- Radio Settings G (802.11g) 120
- Security 122
- Enabling the VAPs 127
- Wi-Fi Protected Access (WPA) 133
- Configuring 802.1X 138
- Status Information 140
- Station Status 143
- Event Logs 145
- STP Status 147
- Chapter 7: Co 149
- Entering Commands 150
- Command Completion 151
- Getting Help on Commands 151
- Showing Commands 151
- SMC AP#show s? 152
- SMC AP#show s 152
- Exec Commands 153
- Configuration Commands 153
- Command Groups 154
- General Commands 155
- Command Line Interface 156
- System Management Commands 159
- APmgmtIP 169
- APmgmtUI 170
- System Logging Commands 177
- System Clock Commands 182
- DHCP Relay Commands 187
- SNMP Commands 189
- Flash/File Commands 204
- RADIUS Client 208
- 802.1X Authentication 214
- 802.1x session-timeout 216
- 802.1x-supplicant enable 217
- 802.1x-supplicant user 217
- MAC Address Authentication 219
- Filtering Commands 222
- WDS Bridge Commands 226
- Spanning Tree Commands 233
- Ethernet Interface Commands 238
- Wireless Interface Commands 243
- Rogue AP Detection Commands 264
- Wireless Security Commands 268
- Link Integrity Commands 278
- IAPP Commands 282
- VLAN Commands 283
- WMM Commands 285
- Appendix A: Troubleshooting 289
- Troubleshooting 290
- 10/100BASE-TX Pin Assignments 291
- Straight-Through Wiring 292
- Crossover Wiring 293
- 8-Pin DIN Connector Pinout 293
- Cables and Pinouts 294
- General Specifications 295
- Specifications 296
- Sensitivity 298
- Transmit Power 299
- V-förmige Halterung 301
- Montieren der Bridge 302
- Ethernet-Kabel 307
- Erdungsleitung 307
- Glossary 309
- Model Number: SMC2890W-AG / 317
- SMC2891W-AG 317
- Pub. Number: 149100034900E 317
- SMC2890W-AG / 318
© 2020, manymanuals-pt.com. Todos os direitos reservados. | 0.156 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Comentários a estes Manuais